ASE A2 Automatic Transmission/Transaxle Practice Test — 15 Free Questions
Fifteen real questions drawn from the ASE Prep Lab A2 question bank, spread across the exam's content areas. Free — no signup, no email. Pick an answer for each question, then open the reveal to check it and read the explanation.
Question 1 (QA-23, Area A — Transmission/Transaxle Diagnosis)
Pink, milky fluid on the transmission dipstick indicates:
Show answer
Answer: C. Coolant emulsified in ATF turns it pink and milky ("strawberry milkshake") and destroys friction-material bonding; the cooler circuit is the classic entry path. Why the others are wrong: A — aging darkens fluid, it does not turn it pink. B produces dark, burnt fluid, not a milky emulsion. D cannot be identified by this appearance.
Question 2 (QA-43, Area A — Transmission/Transaxle Diagnosis)
A permanent DTC remains after the faulty component is replaced and the vehicle is driven once around the block. The technician should:
Show answer
Answer: B. Permanent DTCs are removed by the module's own judgment after the monitor runs — often requiring specific drive conditions or consecutive passes — never by scan-tool command or power interruption. Why the others are wrong: A condemns a part for doing exactly what the system design requires. C is precisely what permanent DTCs are designed to survive. D replaces the module for storing a code correctly.
Question 3 (QA-62, Area A — Transmission/Transaxle Diagnosis)
Engine coolant is found low and the coolant in the reservoir has a reddish, oily film, while the transmission fluid is pink and milky. The shared cause is:
Show answer
Answer: C. The in-radiator cooler is the one place ATF and coolant share a wall; a breach contaminates both systems, each fluid showing in the other. Both systems then need service — and the transmission's friction materials are at risk from the coolant. Why the others are wrong: A and B mix engine oil/coolant or combustion/coolant, not ATF/coolant. D exchanges nothing between fluids.
Question 4 (QA-81, Area A — Transmission/Transaxle Diagnosis)
A vehicle has no TCC lock-up. Scan data shows the TCC solenoid is commanded ON at cruise and the solenoid passes electrical tests. The mechanical/hydraulic checks that remain include all of the following EXCEPT:
Show answer
Answer: C. The thermostat belongs to the engine cooling system and cannot apply a converter clutch. Why the others are wrong: A, B, and D are all genuine hydraulic/mechanical branches of a no-lock-up diagnosis once the electrical command is proven, so none can be the EXCEPT answer.
Question 5 (QA-101, Area A — Transmission/Transaxle Diagnosis)
While monitoring an EPC solenoid's current with a lab scope during a road test, the current pattern drops to zero intermittently and line pressure spikes harsh at the same moments. The fault indicated is:
Show answer
Answer: A. The waveform ties the symptom to the cause in real time: current zero = pressure maximum = harsh shift, repeatedly. Intermittents are caught by recording, not by static tests. Why the others are wrong: B and C cannot switch pressure in step with an electrical dropout. D changes gradually over many shifts, not in spikes.
Question 6 (QA-120, Area A — Transmission/Transaxle Diagnosis)
Technician A says every component named in a code's title should be replaced when the code sets. Technician B says a code names a circuit or system to test, and the failed part is identified by testing, not by the code title. Who is right?
Show answer
Answer: B. A "solenoid circuit" code can be the solenoid, its feed, its ground, its wiring, or its driver — the title names the territory, testing finds the fault. A is the most expensive misconception in electronic diagnosis. Why the others are wrong: A-only and Both endorse title-based replacement. Neither rejects the testing principle.
Question 7 (QA-139, Area A — Transmission/Transaxle Diagnosis)
A dragging brake caliper can imitate a transmission fault by:
Show answer
Answer: D. Anything that loads the powertrain feels like a powertrain fault from the driver's seat; a simple wheel-drag check separates it. Why the others are wrong: A, B, and C claim effects a caliper cannot produce.
Question 8 (QA-158, Area A — Transmission/Transaxle Diagnosis)
A vehicle sets multiple U-codes (lost communication) including with the transmission control module, and the transmission defaults to a failsafe gear when the fault occurs. The diagnosis belongs FIRST to:
Show answer
Answer: D. Communication faults are diagnosed at the network level: powers, grounds, network voltages/termination, and the conditions of the dropout. Internal transmission parts cannot set U-codes. Why the others are wrong: A, B, and C are mechanical parts with no role in network communication.
Question 9 (QA-4, Area A — Transmission/Transaxle Diagnosis)
A technician is identifying an unknown unit before ordering service parts. The RPO/service identification label and the unit's own ID tag disagree with the sales brochure the customer brought in. The identification that governs parts and procedures is:
Show answer
Answer: C. Running changes and multiple available units per model make the unit ID tag plus manufacturer service information the only reliable identification; mid-year units can differ internally. Why the others are wrong: A and B are marketing material, not service data. D alone cannot separate units installed in the same vehicle line.
Question 10 (QB-11, Area B — In-Vehicle Transmission/Transaxle Maintenance and Repair)
A cooler line quick-connect fitting seeps after a radiator replacement. The correct repair is:
Show answer
Answer: C. Quick-connects are seal-and-clip devices; a disturbed O-ring from the radiator job is the expected fault, and seating is verified by pull-test, not hope. Why the others are wrong: A crushes plastic fittings. B is absurd for a fitting seep. D is not a pressure-line repair.
Question 11 (QB-31, Area B — In-Vehicle Transmission/Transaxle Maintenance and Repair)
Two check balls in the same valve body look similar but the diagram specifies different sizes/materials for two locations. Installing them swapped can:
Show answer
Answer: C. Ball specification is circuit tuning; "close enough" placement is a manufactured fault. Why the others are wrong: A and B dismiss specifications as decoration. D overstates the path — the effect is hydraulic behavior, not direct converter damage.
Question 12 (QB-51, Area B — In-Vehicle Transmission/Transaxle Maintenance and Repair)
On units with a selective servo pin (or band adjustment), pin length/adjustment is set to:
Show answer
Answer: A. Pin length is the band's apply geometry: it decides how far the servo travels before the band grips, and both directions of error are failures. Why the others are wrong: B, C, and D are set by other systems entirely.
Question 13 (QB-71, Area B — In-Vehicle Transmission/Transaxle Maintenance and Repair)
After a filter service, the transmission whines and engagement is delayed. The filter is removed and TWO O-ring seals are found stacked at the filter neck — the old seal stayed in the pump bore. The fault mechanism is:
Show answer
Answer: B. The classic filter-service pitfall: the old seal must come out of the bore and be accounted for before the new filter goes in. Why the others are wrong: A inverts the geometry. C and D are disproven by the physical finding.
Question 14 (QC-6, Area C — Transmission/Transaxle Unit Removal, Inspection, and Installation)
The transmission stops 1/8 inch short of the engine block while being mated, and will not seat by hand. The correct action is:
Show answer
Answer: B. Bell housing bolts are clamps, not come-alongs; proper mating is a hand-pressure event on aligned dowels. Why the others are wrong: A is the classic pump-killer. C and D add force to a geometry fault.
Question 15 (QC-30, Area C — Transmission/Transaxle Unit Removal, Inspection, and Installation)
A chain-drive transaxle's drive chain is judged by:
Show answer
Answer: D. Chains are measured wear items; sprockets are replaced with a worn chain when their teeth have hooked to match it. Why the others are wrong: A, B, and C are not measurements.
Answer all 15, then check your score. The explanations above stay open either way — the score never gates the answers.