A4

ASE A4 Suspension & Steering Practice Test — 15 Free Questions

Fifteen real questions drawn from the ASE Prep Lab A4 question bank, spread across the exam's content areas. Free — no signup, no email. Pick an answer for each question, then open the reveal to check it and read the explanation.

Question 1 (QA-12, Area A — Steering Systems Diagnosis and Repair)

A worn steering column upper bearing most commonly produces:

Show answer

Answer: D. The bearing supports the shaft at the wheel; wear shows as rim play and column rattle. Why the others are wrong: A is a wheel bearing/hub symptom. C is brake/alignment territory. B originates at the pump, underhood.

Question 2 (QA-35, Area A — Steering Systems Diagnosis and Repair)

Technician A says power steering fluid type is universal and any red ATF works in every system. Technician B says some systems specify a particular power steering fluid or a specific ATF, and the manufacturer's specification governs. Who is right?

Show answer

Answer: B. Fluid specs vary by manufacturer and seal materials; the reservoir cap and service information name the required fluid. Why the others are wrong: A states the unsafe shortcut. C is impossible — the statements contradict. D denies the governing rule.

Question 3 (QA-57, Area A — Steering Systems Diagnosis and Repair)

A vehicle with speed-sensitive variable assist has steering that is far too light and twitchy at highway speed but normal when parking. The MOST likely cause is:

Show answer

Answer: A. Variable assist reduces assist as speed rises; stuck at full assist, highway steering becomes over-light while parking feels normal. Why the others are wrong: B adds play, not lightness. C increases stability and effort — the opposite symptom. D is a protection fault.

Question 4 (QA-80, Area A — Steering Systems Diagnosis and Repair)

A vehicle darts (changes direction) over bumps without steering input — bump steer. On a parallelogram linkage, a likely mechanical cause is:

Show answer

Answer: A. Bump steer is a geometry fault: linkage arcs that no longer match the suspension's arc steer the wheels as they travel. Why the others are wrong: B influences return and stability, not per-bump toe. C/D cannot steer the car over bumps.

Question 5 (QB-12, Area B — Suspension Systems Diagnosis and Repair)

Excessive front-end dive under braking with good brakes and no fluid leaks is MOST often caused by:

Show answer

Answer: D. Dive is weight transfer the front springs and dampers must control; tired parts let the nose fall. (ASE's own sample item keys dive to weak springs.) Why the others are wrong: B — the bar works in roll, not pitch. C/A cannot produce dive.

Question 6 (QB-30, Area B — Suspension Systems Diagnosis and Repair)

Technician A says on a suspension where the spring seats on the UPPER control arm, the upper ball joint is the load-carrying joint. Technician B says the load-carrying joint is always the lower one. Who is right?

Show answer

Answer: A. The load-carrying joint is whichever joint the spring's force passes through — upper-spring layouts load the upper joint. Why the others are wrong: B states the common-but-wrong absolute; the spring decides, not the position. C/D follow.

Question 7 (QB-48, Area B — Suspension Systems Diagnosis and Repair)

The compressor in an air suspension runs almost constantly and the vehicle stays low. After confirming no major leak is audible, the next checks include:

Show answer

Answer: C. A running compressor with low height = supply or leakage fault: dryer saturation, small leaks, or a tired compressor — found with a systematic leak test. Why the others are wrong: B/A/D cannot consume compressed air.

Question 8 (QB-65, Area B — Suspension Systems Diagnosis and Repair)

The center bolt (center pin) of a leaf spring pack serves to:

Show answer

Answer: C. A sheared center pin lets the axle shift on the spring — thrust/dog-track problems follow. Why the others are wrong: B is done by spring arch/blocks by design, not the pin. A/D are not pin functions.

Question 9 (QB-84, Area B — Suspension Systems Diagnosis and Repair)

Loose or worn rear lateral link bushings under acceleration can cause the rear of the car to:

Show answer

Answer: D. Power-on bushing deflection is a geometry change timed to the throttle — the car changes lane manners with the gas pedal. Why the others are wrong: B is a static height fault. C/A belong to other systems.

Question 10 (QC-11, Area C — Wheel Alignment Diagnosis, Adjustment, and Repair)

Torque steer is:

Show answer

Answer: A. Torque steer is timed to the throttle on FWD cars; it vanishes off-power, which separates it from alignment pulls. Why the others are wrong: B pulls whenever the brake drags, power on or off. C is random, not directional. D pulls with assist regardless of throttle.

Question 11 (QC-32, Area C — Wheel Alignment Diagnosis, Adjustment, and Repair)

All of the following are pre-alignment inspection items EXCEPT:

Show answer

Answer: D. Oil service has no bearing on geometry. Why the others are wrong: A/B/C each change or invalidate readings if skipped: pressure alters height and rolling, height defines the angles, and loose parts make readings unrepeatable.

Question 12 (QC-53, Area C — Wheel Alignment Diagnosis, Adjustment, and Repair)

Scrub radius is changed MOST directly by:

Show answer

Answer: C. Scrub radius is the axis-to-contact-patch distance at the ground; wheel offset moves the patch, changing kickback and steering feel. Why the others are wrong: A/B/D alter forces slightly but do not relocate the patch like offset does.

Question 13 (QC-74, Area C — Wheel Alignment Diagnosis, Adjustment, and Repair)

A customer installed lowering springs and now the front camber is excessively negative beyond the adjustment range. The correct professional response is:

Show answer

Answer: B. Ride height is geometry; the fix addresses the geometry with approved parts, not force or silence. Why the others are wrong: A is prohibited bending. C ships a tire-wearing car without disclosure. D does not restore the angle.

Question 14 (QD-5, Area D — Wheel and Tire Diagnosis and Service)

The last four digits of the DOT tire identification number, "3221," mean the tire was manufactured in:

Show answer

Answer: B. The DOT date code is week-week-year-year — the tire's birth certificate, used for age-based replacement guidance. Why the others are wrong: A misreads the fields as month/year. C inverts them. D invents a plant code in the date field.

Question 15 (QD-23, Area D — Wheel and Tire Diagnosis and Service)

Technician A says a bent steel wheel found during runout measurement should be replaced rather than straightened for road use. Technician B says lateral runout beyond the manufacturer's limit on a wheel can cause a shimmy that balancing will not cure. Who is right?

Show answer

Answer: C. Both are runout doctrine: bent wheels are replaced, and wobble beyond limits is a geometry fault that weights cannot fix. Why the others are wrong: A-only misses the balance limit. B-only misses the replacement rule. D denies both.

Answer all 15, then check your score. The explanations above stay open either way — the score never gates the answers.

Keep going with ASE A4