A5

ASE A5 Brakes Practice Test — 15 Free Questions

Fifteen real questions drawn from the ASE Prep Lab A5 question bank, spread across the exam's content areas. Free — no signup, no email. Pick an answer for each question, then open the reveal to check it and read the explanation.

Question 1 (Q1.2-1, Area A — Hydraulic, Power Assist & Parking Brake Systems)

A driver applies 120 lb of force to a brake pedal with a 5:1 pedal ratio. The master cylinder bore is 1.00 inch. Ignoring booster assist, what line pressure is produced?

Show answer

Answer: C. Pushrod force = 120 × 5 = 600 lb. Piston area = π × (0.50)² = 0.785 in². P = F ÷ A = 600 ÷ 0.785 = 764 psi. Why the others are wrong: A uses the pedal force without the pedal ratio (120 ÷ 0.785). B is the pushrod force in pounds, not pressure. D uses the diameter as the radius (area 3.14 in²).

Question 2 (Q1.2-2, Area A — Hydraulic, Power Assist & Parking Brake Systems)

The 764 psi from Q1.2-1 acts on a front caliper piston 2.60 inches in diameter. Approximately how much clamp force does the piston produce?

Show answer

Answer: C. Area = π × (1.30)² = 5.31 in². F = P × A = 764 × 5.31 ≈ 4,060 lb. Why the others are wrong: A divides pressure by diameter. B multiplies pressure by diameter instead of area. D equates pressure with force — the exact confusion Pascal's law questions test.

Question 3 (Q1.2-4, Area A — Hydraulic, Power Assist & Parking Brake Systems)

All of the following statements about a sealed hydraulic brake circuit are true EXCEPT:

Show answer

Answer: D. Pascal's law: pressure is transmitted equally and undiminished; distance does not change it. Why the others are wrong: A, B, C are each correct statements of the lesson's core rules — an EXCEPT item requires all three to be true, and they are.

Question 4 (Q1.2-5, Area A — Hydraulic, Power Assist & Parking Brake Systems)

Technician A says that if the master cylinder piston and a wheel cylinder piston have the same area, the wheel cylinder produces the same force the pushrod applies — no multiplication. Technician B says that doubling a caliper piston's area doubles its clamp force at the same line pressure. Who is right?

Show answer

Answer: C. A: equal areas → F_out = P × A = F_in. B: F = P × A, so doubling A doubles F at constant P. Why the others are wrong: A-only and B-only each reject one correct statement; D rejects both.

Question 5 (Q1.4-4, Area A — Hydraulic, Power Assist & Parking Brake Systems)

Technician A says that if the primary circuit develops a leak, the primary piston travels forward until it mechanically contacts the secondary piston, so the secondary circuit can still build pressure. Technician B says that if the secondary circuit develops a leak, the secondary piston travels until it bottoms at the front of the bore, so the primary circuit can still build pressure. Who is right?

Show answer

Answer: C. Both are the tandem cylinder's designed failure behaviors — one circuit is lost, pedal travel increases, the warning lamp lights, and the other circuit still stops the vehicle. Why the others are wrong: A-only/B-only each deny a real mechanism; D denies the entire point of the tandem design.

Question 6 (Q1.5-1, Area A — Hydraulic, Power Assist & Parking Brake Systems)

A brake pedal slowly sinks under steady pressure at a stoplight. The fluid level is correct and no external leaks are found. Both master cylinder outlets are plugged and the pedal still sinks. What is the MOST likely cause?

Show answer

Answer: C. With the outlets plugged, nothing downstream participates; sinking means fluid is escaping past the primary cup inside the bore. Why the others are wrong: A — the booster changes assist and pedal feel, not hydraulic holding. B and D are downstream of the plugs and were removed from the test by them.

Question 7 (Q1.5-4, Area A — Hydraulic, Power Assist & Parking Brake Systems)

After a master cylinder replacement, a vehicle's brakes drag more and more the longer it is driven. Technician A says the booster pushrod is too long, holding the primary piston forward so the compensating port stays covered. Technician B says the pushrod is too short. Who is right?

Show answer

Answer: A. A too-long pushrod prevents full piston return; expansion pressure can't vent (Lesson 1.4's mechanism), and heat makes it self-apply. A too-short pushrod causes excessive free play and a low pedal — the opposite complaint. Why the others are wrong: B names the wrong direction of the same adjustment. C is impossible — one pushrod can't be both. D denies the classic post-replacement cause.

Question 8 (Q2.2-4, Area B — Drum Brakes)

Technician A says a drum may be machined as long as its diameter after machining stays at or below the stamped discard dimension, with wear margin considered. Technician B says blowing out a drum with compressed air is acceptable if the shop door is open. Who is right?

Show answer

Answer: A. B states the prohibited practice — brake dust is wet-washed or HEPA-vacuumed, never blown. Why the others are wrong: B-only/C legitimize the dust violation; D denies the machining rule.

Question 9 (Q2.3-2, Area B — Drum Brakes)

A fatigued (heat-weakened) return spring most likely causes:

Show answer

Answer: A. Weak return = incomplete retraction = a shoe that never fully leaves the drum. Why the others are wrong: B is hydraulic bypass. C is nonsense. D — springs affect service braking first.

Question 10 (Q3.2-2, Area C — Disc Brakes)

Pads are replaced:

Show answer

Answer: B. Axle-set replacement keeps friction symmetric. Why the others are wrong: A builds a pull. C waits for one alarm type. D ignores wear entirely.

Question 11 (Q3.5-4, Area C — Disc Brakes)

A rear caliper with an integrated parking brake needs new pads. The piston will not retract with a C-clamp. The correct next step is:

Show answer

Answer: B. Screw-in pistons retract by rotation; forcing destroys the internal adjuster. Why the others are wrong: A/C escalate the damage. D is not a procedure.

Question 12 (Q3.9-1, Area C — Disc Brakes)

Pads tapered identically on both front wheels most likely share:

Show answer

Answer: B. Bilateral symmetry indicts a shared condition, not a shared part. Why the others are wrong: A can't be on both wheels. C tapers nothing. D is system-wide, not geometric.

Question 13 (Q4.2-1, Area D — Electronic Brake Control: ABS/TCS/ESC)

At rest (no ABS event), the isolation valve is ______ and the dump valve is ______.

Show answer

Answer: B. Resting state = transparent plumbing: pressure passes through, none escapes. Why the others are wrong: A would block and vent every normal stop. C/D break base braking.

Question 14 (Q4.4-4, Area D — Electronic Brake Control: ABS/TCS/ESC)

ESC became standard on U.S. light vehicles under:

Show answer

Answer: B. FMVSS 126 is the stability-control standard. Why the others are wrong: A is brake fluid (Module 1). C/D are the wrong authorities.

Question 15 (Q4.7-3, Area D — Electronic Brake Control: ABS/TCS/ESC)

The scan tool cannot communicate with the EBCM. Before replacing anything, the technician should:

Show answer

Answer: B. Case 5's moral: starved modules look dead. Why the others are wrong: A is the expensive error. C/D flail.

Answer all 15, then check your score. The explanations above stay open either way — the score never gates the answers.

Keep going with ASE A5