ASE A6 Electrical/Electronic Systems Practice Test — 15 Free Questions
Fifteen real questions drawn from the ASE Prep Lab A6 question bank, spread across the exam's content areas. Free — no signup, no email. Pick an answer for each question, then open the reveal to check it and read the explanation.
Question 1 (QA-10, Area A — General Electrical/Electronic System Diagnosis)
A technician is dispatched a vehicle with a "battery light on" complaint but no other information. The MOST efficient first moves are to:
Show answer
Answer: B. Verify, look, and research before testing components — the sequence that finds causes instead of swapping parts. Why the others are wrong: A and D are parts-first guesses. C is an outdated, damaging practice that can spike module voltage; it is never the correct test.
Question 2 (QA-30, Area A — General Electrical/Electronic System Diagnosis)
Three resistors of 2 Ω, 4 Ω, and 6 Ω are connected in series across a 12 V source. The total resistance of the circuit is:
Show answer
Answer: C. Series resistances simply add: 2 + 4 + 6 = 12 Ω (and the circuit draws 12 ÷ 12 = 1 A). Why the others are wrong: A is the parallel equivalent of the same three resistors. B doubles the sum without basis. D is only the largest single resistor.
Question 3 (QA-49, Area A — General Electrical/Electronic System Diagnosis)
Technician A says a DTC naming a sensor means that sensor has failed and replacing it is the correct first step. Technician B says a DTC identifies a circuit or system that reported out-of-range values; the cause can be wiring, power, ground, a related component, or the sensor itself, and must be isolated by testing. Who is right?
Show answer
Answer: B. Codes are test plans, not parts orders: most sensor codes mature from circuit faults, and the module usually cannot tell a bad sensor from a bad wire feeding it. Why the others are wrong: A-only and Both credit the replace-first approach that creates comebacks. Neither denies B's correct description.
Question 4 (QA-69, Area A — General Electrical/Electronic System Diagnosis)
On a wiring schematic, a wire that ends in the ground symbol (a series of horizontal lines of decreasing width, or a chassis-ground marker) indicates that the conductor:
Show answer
Answer: A. The ground symbol marks where the circuit returns to the battery's negative side; every load's path must end there for current to flow. Why the others are wrong: B — a cut wire is drawn with an open end, not a ground symbol. C — reference circuits are labeled as such. D confuses shields (drawn as dashed enclosures) with ground connections.
Question 5 (QB-7, Area B — Battery and Starting System Diagnosis and Repair)
A vehicle was jump-started twice this week. In the shop, the battery shows 10.9 V open-circuit but the charging system tests normal. Before condemning the battery, the technician should:
Show answer
Answer: D. Testing a discharged battery condemns batteries that were merely empty. Charge first, then test the capacity. Why the others are wrong: A — the charging system already tested normal. B skips the required recharge-and-retest sequence. C guesses at a cause the resting voltage alone does not prove.
Question 6 (QB-34, Area B — Battery and Starting System Diagnosis and Repair)
Service information for a particular vehicle prohibits conventional jump starting and designates specific remote jump posts and a maximum booster voltage. The technician should:
Show answer
Answer: A. Manufacturers specify jump posts and limits to protect modules from surges and to route current through designed paths; the vehicle-specific procedure governs. Why the others are wrong: B ignores the prohibition and its reasons. C doubles the voltage — a module-killing mistake. D overcorrects; the vehicle can be started by its specified method.
Question 7 (QC-4, Area C — Charging System Diagnosis and Repair)
A charge lamp flickers and system voltage dips mainly at idle and during steering loads, then recovers at cruise. A likely cause is:
Show answer
Answer: B. Speed- and load-dependent intermittency points at the mechanical/rotating interface — brush contact and belt grip are worst at low rpm and high accessory torque. Why the others are wrong: A would distort every test constantly. C would stop charging entirely. D — diode failures reduce output and add ripple steadily rather than flickering with load changes.
Question 8 (QC-19, Area C — Charging System Diagnosis and Repair)
A scan tool shows the PCM commanding charging (field control signal active and varying), the alternator's feeds and grounds test good, but output is zero. The fault is:
Show answer
Answer: D. Diagnosis by exclusion: command present, power present, ground present, drive present — the failure is inside the box. Why the others are wrong: A is disproven by the active command. B was proven in the premise. C — a missing belt would be found on inspection and would not match "drive present."
Question 9 (QD-5, Area D — Lighting Systems Diagnosis and Repair)
A tail lamp glows dimly whenever the brake pedal is pressed, even though its own circuit is switched off. This is the classic symptom of:
Show answer
Answer: A. Ground-side backfeeding makes lamps do haunted things: with the proper ground path resistive, current improvises through neighboring filaments, lighting lamps dimly in wrong combinations. Why the others are wrong: B would light the brake lamps at full brightness, not glow the tail lamp dimly. C does not create cross-lighting. D dims everything rather than cross-feeding one lamp.
Question 10 (QD-23, Area D — Lighting Systems Diagnosis and Repair)
Technician A says turn signal flash rate is driven directly by engine rpm. Technician B says on module-controlled systems the flash rate and bulb-out hyperflash are software behaviors of the body control module, which is why both sides can behave independently. Who is right?
Show answer
Answer: B. Flash timing is a flasher/module function; electronic control makes per-side behavior and diagnostics possible. Engine speed has no direct role. Why the others are wrong: A-only and Both credit a mechanical fiction. Neither denies B's accurate description.
Question 11 (QE-14, Area E — Body Electrical Systems Diagnosis and Repair)
The steering wheel audio and cruise buttons are all inoperative, while every other steering wheel function works. A likely fault area is:
Show answer
Answer: C. All the dead functions share one path: the switch assembly and its rotating connection. Testing the ladder/signal at the column connector separates switch pack from clockspring from module. Why the others are wrong: A and D are audio endpoints, not the shared input path. B affects cruise cancel logic only, not audio buttons.
Question 12 (QE-34, Area E — Body Electrical Systems Diagnosis and Repair)
Cruise control will not set, and the only stored code is for the brake pedal position switch circuit. The connection is:
Show answer
Answer: C. Cruise's first safety input is the brake switch; an implausible signal vetoes engagement exactly like QE-32's hood switch vetoes remote start. Why the others are wrong: A and B understate the switch's roles — it is a multi-system input. D is a vibration concern.
Question 13 (QE-55, Area E — Body Electrical Systems Diagnosis and Repair)
On a rear defroster grid, only the middle horizontal lines clear; the top and bottom lines stay frosted. The cause is:
Show answer
Answer: A. Parallel-line architecture localizes damage: relay, fuse, or feed faults would kill the whole grid at once, not selected lines. Why the others are wrong: B, C, and D are all whole-grid faults contradicted by the working middle lines.
Question 14 (QE-75, Area E — Body Electrical Systems Diagnosis and Repair)
A no-crank vehicle has a good battery, a silent starter, and an illuminated security lamp; the scan tool shows the security module is in "starter disable" status. The correct path is:
Show answer
Answer: A. A commanded disable is a system decision to trace, not a starter to replace; when authorization is restored, the original starter will work. Why the others are wrong: B and C replace parts the disable is deliberately blocking. D defeats a security system — never a repair.
Question 15 (QE-95, Area E — Body Electrical Systems Diagnosis and Repair)
A front seat with an occupant detection system (OCS) has its seat cushion/sensor replaced. After installation, the airbag lamp is on with an OCS fault. The required step is:
Show answer
Answer: A. Weight-sensing systems are calibrated judgments, not parts swaps; the initialization teaches the baseline every deployment decision depends on. Why the others are wrong: B falsifies the baseline in the dangerous direction. C erases evidence without calibration. D deletes a safety function.
Answer all 15, then check your score. The explanations above stay open either way — the score never gates the answers.