ASE A8 Engine Performance Practice Test — 15 Free Questions
Fifteen real questions drawn from the ASE Prep Lab A8 question bank, spread across the exam's content areas. Free — no signup, no email. Pick an answer for each question, then open the reveal to check it and read the explanation.
Question 1 (QA-10, Area A — General Diagnosis)
An engine consumes oil, has blow-by at the oil filler, and wet compression rises significantly over dry compression on all cylinders. The indicated fault is:
Show answer
Answer: D. Oil added for the wet test temporarily seals the ring-to-wall gap; a large wet-over-dry rise on all cylinders plus blow-by confirms ring sealing loss. Why the others are wrong: A and B would not respond to oil in the cylinder this way. C can raise oil consumption but does not change compression readings.
Question 2 (QA-29, Area A — General Diagnosis)
A relative compression test (cranking current waveform) shows one cylinder's current peak noticeably lower than the others. This correlates with which power-balance expectation for that cylinder?
Show answer
Answer: D. Lower cranking current peak = lower compression on that cylinder = weaker contribution = smaller drop when killed. The two tests corroborate each other. Why the others are wrong: A inverts the relationship. B is true but answers nothing about the flagged cylinder. C contradicts the waveform.
Question 3 (QA-47, Area A — General Diagnosis)
When verifying valve adjustment on an engine with adjustable rocker arms, the measurement must be made:
Show answer
Answer: D. Lash is defined with the valve fully closed on the cam's base circle; the manufacturer's procedure governs temperature and method, which vary by engine. Why the others are wrong: A and C state absolutes the procedure does not support. B measures at the one position where lash does not exist.
Question 4 (QA-64, Area A — General Diagnosis)
A schematic shows a wire changing color after a connector (for example, RED before the connector, RED/BLK after). When tracing a voltage fault, this tells the technician:
Show answer
Answer: D. Color changes at connectors are designed, not defects; schematic-guided tracing prevents "lost" circuits at bulkheads. Why the others are wrong: A, B, and C treat a normal convention as a fault.
Question 5 (QB-6, Area B — Ignition System Diagnosis and Repair)
A coil-on-plug engine misfires on cylinder 5 only. Swapping the coil to cylinder 2 moves the misfire to cylinder 2. The conclusion is:
Show answer
Answer: C. A fault that follows the part belongs to the part. Why the others are wrong: A and B are faults that would have stayed on cylinder 5. D multiplies failures beyond the evidence.
Question 6 (QB-30, Area B — Ignition System Diagnosis and Repair)
Spark plug wires (where equipped) with resistance far above specification cause:
Show answer
Answer: A. Secondary resistance consumes spark energy and adds to the voltage the coil must produce; the failure shows when demand peaks. Why the others are wrong: B, C, and D are systems wire resistance cannot influence.
Question 7 (QC-7, Area C — Fuel, Air Induction and Exhaust Systems)
A no-start vehicle has good spark and 0 psi fuel pressure, but the pump cannot be heard priming with the key on. The diagnosis should proceed to:
Show answer
Answer: A. A silent pump with no pressure is an electrical-or-pump question; circuit tests answer it for the price of a test light instead of a fuel tank drop. Why the others are wrong: B skips the cheap half of the diagnosis. C and D address systems not implicated by a silent pump.
Question 8 (QC-25, Area C — Fuel, Air Induction and Exhaust Systems)
A no-prime complaint on a vehicle with a fuel pump control module is diagnosed by checking:
Show answer
Answer: C. A module-controlled pump has three suspects — command, module, and pump — and scan data plus circuit tests separate them in that order. Why the others are wrong: A and B test one item each and stop. D is the ignition system.
Question 9 (QC-43, Area C — Fuel, Air Induction and Exhaust Systems)
A variable intake runner system stuck in the long-runner position typically causes:
Show answer
Answer: C. Runner systems tune intake length to rpm: long for low-end torque, short for high-end flow; stuck long sacrifices the top end. Why the others are wrong: A describes stuck-short behavior. B and D are not runner-position effects.
Question 10 (QD-7, Area D — Emissions Control Systems)
An EGR valve stuck OPEN (or opening at idle when it should be closed) causes:
Show answer
Answer: D. EGR is commanded off at idle precisely because a small engine charge cannot burn diluted; a valve stuck open applies full-time dilution. Why the others are wrong: A is the stuck-CLOSED/too-little-EGR symptom under load. B and C are not EGR-stuck-open effects.
Question 11 (QD-31, Area D — Emissions Control Systems)
The EVAP system's function is to:
Show answer
Answer: B. EVAP is a sealed vapor management system: store vapors in charcoal, then meter them into the intake under PCM control. Why the others are wrong: A is what the system exists to prevent. C and D are fuel-delivery functions.
Question 12 (QE-12, Area E — Computerized Engine Controls)
A DTC is typically stored with MIL illumination only after the fault fails on two consecutive trips for many emissions monitors because:
Show answer
Answer: B. Two-trip design is deliberate filtering: real faults repeat, glitches pass. Why the others are wrong: A and C invent processing limitations. D overstates — some monitors (severe misfire, some circuit faults) are one-trip.
Question 13 (QE-31, Area E — Computerized Engine Controls)
A customer complains of poor fuel economy with no codes and no other symptom. A systematic check should include:
Show answer
Answer: A. Mileage complaints are accounting problems: every small loss adds up, and most causes are mundane. Why the others are wrong: B and C each bet everything on one part. D starts with the least likely, most invasive test.
Question 14 (QE-50, Area E — Computerized Engine Controls)
A voltmeter measures 12.6 V at a component's power terminal with the connector DISCONNECTED, but only 8.9 V with the component connected and operating. This indicates:
Show answer
Answer: B. This is the founding lesson of loaded testing: open-circuit voltage proves almost nothing; sag under load is resistance confessing. Why the others are wrong: A denies the 3.7 V loss. C — the component may be fine and starved. D is not established by these readings.
Question 15 (QE-16, Area E — Computerized Engine Controls)
A code described as "history" or "stored" with no current failure, after many successful trips, will typically:
Show answer
Answer: B. OBD II heals: passing trips extinguish the lamp and continued passes age the code out of memory. Why the others are wrong: A and C contradict the healing design. D is a parts leap.
Answer all 15, then check your score. The explanations above stay open either way — the score never gates the answers.